Cart
SHOTGUN SERVICE
| Inspect firearm and prepare written quote | $40.00 |
| Professional boresighting | $15.00 |
| Professional scope mounting and boresighting | $30.00 |
| Professional scope mounting and boresighting (Includes lapping in the rings) | $50.00 |
| Minimum charge | $20.00 |
| Labor half hour | $40.00 |
| Labor one hour | $80.00 |
| Complete Clean, disassemble, safety check, oil and reassemble (rust removal and or excessively dirty firearms are additional) | |
| Most pumps & Autos Win 97, Rem 11’s, Brwn auto-5's and similar models Doubles & O/U’s High grade Doubles & O/U’s with sidelocks |
$60.00 $80.00 $100.00 $120.00 |
| Cut, crown and reset bead (New Bead additional) | $80.00 |
| Cut and crown only on single barrels | $60.00 |
| Cut and crown O/U or SxS | $120.00 |
| Drill and tap for sight bead (one) | $35.00 |
| Drill and tap for sight beads (two, same set up) | $60.00 |
| Drill and tap for top mounts | $80.00 |
| Drill and tap for side mount (starting at) | $80.00 |
| Solder cantilever mount to barrel, includes rebluing | $160.00 |
| Solder rifle sights on plain barrel (includes Remington sights and matte bluing) | $200.00 |
| Open choke to your specs (all gauges) price is per barrel | $80.00 |
| Open choke on chrome bores (10,12 & 20) | $100.00 |
| Lengthen chamber to 3" | $80.00 |
| Lengthen chamber to 3", chrome lined | $100.00 |
| Lengthen forcing cone | $80.00 |
| Lengthen forcing cone, chrome lined | $100.00 |
| Install Uncle Mike's swivels any style (swivels not included) | $40.00 |
| Resolder shotgun ribs (Please see the gunsmith for a quote) | Price on Request |
| Remove dents and straighten barrels at customer risk (please bring in for quote) | Price on Request |
| Install wire shell catcher in most autos | $80.00 |
| Inlet to drop or raise stock on 870,11/87,303,390 etc. | $80.00 |
| Convert 29/16" Browning Auto 5 or Win. M 12 to 2 3/4" | $300.00 |
| Winchester 1200 1300 1400 1500 ejector repair convert Winchester shotgun from old pinned-in ejector to new retainer style (labor only) | $80.00 |
| Poly Choke Ventilated and International rib Installation (labor only) | $100.00 |
| Convert 1100 Mag to shoot 2 3/4" | $80.00 |
| Convert 1100 20ga. LT barrel to short tang LW style | $100.00 |
| Repair broken interceptor latch stud on 1100/1187 Without rebluing the receiver Includes rebluing the receiver to a Matte finish | $100.00 $140.00 |
| Replace barrel alignment stud on the 1100/1187, includes rebluing of receiver | $120.00 |
| Replace or resolder action spring tube on the 1100/1187, includes rebluing of receiver. (new tube additional) | $160.00 |
| Resolder original magazine tube on 1100/1187, includes rebluing | $160.00 |
| Replace magazine tube on 1100/1187, includes fitting of new barrel support and rebluing (mag tube assembly additional) |
$200.00 |
| Resolder gas cylinder to barrel and reblue | $160.00 |
| Open 870 to 3" Mag, includes chamber and ejector work (new ejector spring additional) | $160.00 |
| Replace 870 ejector spring only if possible (parts additional) | $60.00 |
| Replace 870 ejector & spring (parts additional) Includes fitting the rivets as flush as possible and them cold bluing them Includes fitting the rivet flush and rebluing the receiver | $80.00 $120.00 |
| Pin 870 barrel to receiver for accuracy (eliminates barrel movement) | $60.00 |
| Trigger job on Remington 870, 1100 or 1187 using a Timney Sear kit (kit additional) | $60.00 | Timney sear & sear spring kit | $89.99 |
| Open choke to your specs (all gauges) | $80.00 |
| Open choke on chrome bores (10,12 & 20) | $100.00 |
| When installing chokes on plain barrels (non-vented bbls), an additional charge for the installation of a front sight base is required. Parts not included | $60.00 |
| Choke installs on barrels with chrome lined bores, additional | $40.00 |
