FREE SHIPPING On Orders Over $50

Your Session is About to Expire!

What Would You Like To Do?

Renew My Session
Log Out
3 Days Online Only - Save 15%, No Minimum - use code: FOOLS15


General Labor Rates

Inspect firearm and prepare written quote $40.00
Professional boresighting $15.00
Professional scope mounting and boresighting $30.00
Professional scope mounting and boresighting / includes lapping in the rings $50.00
Minimum charge $20.00
Labor half hour $40.00
Labor one hour $80.00


General Rifle Service

Complete clean, disassemble, safety check, oil and reassemble (rust removal and or excessively dirty firearms are additional)
    Bolt Actions, Pumps, Levers & Auto rifles $60.00
    Double Rifles & Drillings $120.00
Check headspace $40.00
Make chamber cast $60.00
Lap barrel $80.00
Cut and crown average barrel (sight work additional) $80.00
Recrown only $60.00
Install new bolt handle, (handle not included) starts at $200.00
Inlet new bolt handle to stock and receiver $60.00
Install tactical bolt knob (parts not included) $120.00
Checker bolt handle (per panel) $100.00
Drill & Tap (per hole) $20.00
Inlet stock for peep sights or side mounts $80.00
Jewel bolt $120.00
Jewel extractor $80.00
Jewel follower $120.00
Zero in rifle at range, ammo not included $100.00
Glass bed finished rifle, starting at $100.00
Install aluminum pillars and glass bed $160.00
Inlet & glass bed semi-inlet stock $80.00/hr
Dovetail .22 rifle for tip-off rings $80.00
Dovetail for open sights (per cut) $60.00
Dovetail front and rear same set up $100.00
Trigger work on request (starting price) $80.00
Rechamber most rifles (bolt, extractor & feeding work additional) starting at $180.00
Mill model 70 Win. & 700 Rem. for stripper clip $180.00
Install Uncle Mike's swivels any style (swivels not included) $40.00
Fit low swing safety Timney, Wisner or Dayton Trasiter (parts additional) $100.00
Install three position safety (safety not included) $80.00/hr
Engrave or electrochemically etch the caliber into the side of a barrel (rebluing additional) $40.00
Install barrel cleaning hole in Ruger 10/22 receiver
(Permits barrel cleaning from the rear without removing the barrel)


Remington Rifle Service

Convert 700 to Sako style extractor (parts additional) $160.00
Convert 742 to a pump action (includes all parts and synthetic stock and forend) $350.00
Alter 760 From 35 Rem. to 358 Win or 35 Whelen $200.00
Solder bolt handle back on 700, includes rebluing handle area $120.00
Convert 700 ADL to BDL style (parts additional) $100.00
Replace rivet-in extractor on 700 (parts additional) $60.00
Replace rivetless extractor on 700 (parts additional) $40.00
Safety Modification on 700 (Remington pays $30.00 customer pays $30.00) $60.00
Trigger job on Remington 7400, 7600, 750, 7615 using a Timney Sear kit (kit additional) $60.00
Timney sear & sear spring kit $89.99


Marlin Centerfire Lever Service

Convert your Marlin lever gun to a takedown gun, requires refinishing $550.00
Install Wild West bear proof ejector for increased reliability, available in blue or silver, includes part and installation $45.00
Install Wild West custom trigger, gives 2 to 3lb trigger pull. This is a must for Marlin owners, available in blue or silver, includes part and installation $120.00
Replace factory lever with a Wild West big loop lever for use with gloves, available in blue and silver, includes part and installation $180.00
Upgrade from the factory plastic magazine follower to a machined aluminum follower for better performance and increased longevity. Hard anodized in bright red for visibility, includes part and installation $40.00


AR-15 Service

Complete disassemble, clean, safety check, oil and reassemble $80.00
Maintenance rebuild (includes all new springs, new gas rings, complete disassemble, clean, safety check, oil and reassemble $120.00
Magazine maintenance rebuild 3-pack (includes new follower spring, MAGPUL self-leveling follower and complete cleaning of three of your magazines) $45.00
Upper / Lower enhancement bundle (includes adjusting the upper to lower receiver fit and refinishing with a matte black moly coating) $200.00
Convert your .223 to .22LR. Practice your sight picture and trigger pull by shooting inexpensive .22LR ammo. (includes installation of new bolt carrier, bolt assembly and one 10rnd magazine made by CMMG) $240.00
Additional 10rd magazines for the above (black) $39.99
Additional 26rd magazines for the above (black) $39.99
Completely assemble a lower from parts kit $80.00
Install custom triggers from makers like Rock River, Geissele, JP Ent., Chip McCormick, Jewell, etc. $80.00/hr
Install A2 front sight base on custom barrel (includes machining for taper pins) $80.00
Thread barrel for brake or flash hider $100.00
Custom sights available from Trijicon, Aimpoint, JP Ent and many more Price on Request
Install accessory handrail, forend, or free float tubes, many variations Price on Request
Custom grips available from Hoge, MAGPUL, Command Arms and many more Price on Request