Cart
Gander Moutain uses the following quality barrel manufacturers:
Cut rifled barrels - Krieger, Badger & Channlynn; Button rifled or forged - Douglas, Shilen, Hart & E.R. Shaw
| Custom barrel installation package (includes complete cleaning, squaring bolt face and receiver, lapping the locking lugs, threading, chambering and headspacing, standard throating, crown of your choice and standard 320 bluing) | $320.00 |
| Economy barrel installation package, includes fitting, chambering, standard crown and bluing (Available on pre-threaded short chambered barrels only) |
$200.00 |
| Up-charge for single shot rifles like Ruger No.1 | $80.00 |
| Up-charge for Win 70 pre 64, Springfields & Enfields (Extractor cut) | $80.00 |
| Fluting | Starting at $200.00 |
| Duplicate your barrels original contour | $120.00 |
| Open bolt face and rails (average cost $150) | $80.00 |
| Inlet your stock for new barrel (average cost $60) | $80.00 |
| Engrave or electrochemically etch the caliber on the barrel | $40.00 |
| Barrel prices can vary greatly depending upon material, contour, caliber, length and twist rates. | |
|
|
1. Before firing a shot, the barrel must be thoroughly cleaned. The bore must be free of any oil and/or packing grease. | |
2. Fire a single shot and clean the barrel thoroughly. Repeat this five times. | |
3. Fire three shots and clean the barrel. Repeat this five times. This helps burnish the bore and reduce copper fouling and powder residue buildup. | |
4. Your barrel is now broken-in and should be thoroughly cleaned after every ten rounds to maintain optimum accuracy. | |
|
|
| Reline most .22 rifles | $160.00 |
| Redman 1-16 twist .22 cal barrel liner 25" (used for LR or WRM) | $40.00 |
| Redman 1-20 twist .22 cal barrel liner 25" (used for .22 short) | $40.00 |
| Redman 1-16 twist .22 cal barrel liner 32" (used for LR or WRM) | $80.00 |
| Redman 1-20 twist .22 cal barrel liner 32" (used for .22 short) | $80.00 |
| Convert your bolt action .22LR to .17 Mach II | $140.00 |
| Convert your bolt action .22 Mag to .17HMR | $140.00 |
| We use premium cut rifled barrels by Krieger | |
| • Manufactured to the same internal and external specifications as all Krieger match barrels. | |
| • 30 caliber, 4-groove in stainless steel or chrome moly steel. | |
| • Stainless barrels are left in-the-white. | |
| • Chrome moly barrels are Parkerized. | |
| • Barrels are completely turned, threaded, and milled with one exception; approximately .010" to .020" material is left on the barrel so our gunsmith can bring it into proper timing when fitted. | |
| • The gas port is drilled into a groove; gas cylinder, receiver threads, feed ramps, and extractor groove are timed off this groove. |
|
|
| • Available in two patterns: a heavy and a lighter G.I. contour (Mil. Spec. John C. Garand Match Legal). | |
| • Heavy pattern measures 1.100" from the breech until it tapers down to .726" at the front handguard, rear slot. | |
| • Heavy pattern barrels require wood to be removed from the forearm and upper handguard (see prices for stock inletting for a new barrel on page 6). |
|
|
| Available in SS or CM, 1-10, 1-11, or 1-12 twist. Please specify .308 Win. or .30-06 caliber. (Weight 3.5 lbs.) | $360.00 |
|
|
| Available in CM only, 1-10, 1-12, or 1-14 twist, .30-06 caliber only. (Weight 2.75 lbs.) | $360.00 |
|
|
| Includes lapping lugs, chambering, crowning, headspace, polish chamber, and reaming front hand guard and band on gas cylinder to clear barrel. | $240.00 |
|
|
| • Available in two contours: a heavy pattern and the Marine Corps DMR pattern. | |
| • Heavy pattern is a full 1.000" diameter from the breech to the operating rod guide and continues at .990" diameter forward to the gas cylinder. | |
| • 1" band type operating rod guide included, but not installed with all heavy pattern barrels. |
|
|
| Available in SS or CM; 1-10, 1-11, or 1-12 twist. 22" length (Weight 3.5 lbs.) | $360.00 |
|
|
| The same contour used by the U. S. Marine Corps. Only available in SS; 1-12 twist, 22" length (Weight 2.8 lbs.) | $360.00 |
|
|
| Fit barrel to action, includes lapping lugs, chambering, crowning, headspace, and polish chamber; also fitting op rod guide, gas cylinder and flash suppressor. | $240.00 |
